- What is the difference between a Vortec 350 and a regular 350?
- How can you tell if a 350 head is a Vortec?
- What is the difference between TBI and vortec?
- Are Vortec heads worth it?
- How much horsepower can a Vortec 350 make?
- What cars came with Vortec heads?
- Can I put Vortec heads on a 350 TBI?
- How much HP can Vortec heads make?
- What year is the best Chevy 350 engine?
- Is the 350 Vortec a good engine?
- What is so special about a Vortec engine?
- How much HP do heads add?
- Can you put 400 heads on a 350?
- Are all center bolt heads vortec?
- Can you convert a TBI to a Vortec?
What is the difference between a Vortec 350 and a regular 350?
The Vortec combustion chamber is a kidney-shaped design that promotes better combustion and will have the spark plug located near the center of the chamber.
The regular 350 head utilizes a 90 degree intake bolt angle while the Vortec makes do with a 72 degree bolt angle..
How can you tell if a 350 head is a Vortec?
Vortec heads have the “sawtooth” pattern casting mark on the end of the heads. The bowl area is wide around the valve guide – much wider than the old GM cast iron ‘camel-hump’ heads. The intake and exhaust valves and valve seats have a three-angle grind from the factory.
What is the difference between TBI and vortec?
The differences between them are that the TBI had the injectors right in front of the throttle plate, where the Vortec placed the injectors behind the throttle plate; and the TBI was a speed density system, whereas the Vortec used a mass airflow system to manage the fuel-injection system.
Are Vortec heads worth it?
vortec heads are one of the cheapest hp gain and they’ll give you better gas mileage. For the center bolt valve covers the ones for the vortec heads are taller then the center bolt valve covers you find on non-vortec heads.
How much horsepower can a Vortec 350 make?
240 HPOriginally Answered: How much horsepower does a 350 Vortec engine have? Somewhere around the 240 HP region ( In stock as in installed trim ) .
What cars came with Vortec heads?
Re: Which vehicles came with Vortec heads? ( 96 thru 99 Chevy and GMC pickups, Suburbans, Tahoe, and Blazers. There were two types of Vortec heads, small heads were used on the small V-8 truck engine, the larger L31 heads were used on all 5.7 V-8s. The ones you want are L31, 5.7 heads.
Can I put Vortec heads on a 350 TBI?
The Vortec heads will flow better than stock heads. If you plan on running the same cam or a cam up to . 460 lift, the heads will be fine. The use of the Performer with the TBI adaptor will also improve performance.
How much HP can Vortec heads make?
GM Vortec cylinder heads are used with a Comp Cams Xtreme Energy 262° camshaft to produce 390 HP and 426 ft-lbs of torque. These numbers are made with 87 octane, while most of the combos on my site used 92 or 93 octane gasoline.
What year is the best Chevy 350 engine?
L31 (2002) From a purely technical standpoint, the most recent version of the Chevy 350 would naturally be the best of the bunch. Marketed as the “Vortec 5700” engine, but known internally by the moniker of L31, this engine was used primarily in GM vans and trucks until 2002.
Is the 350 Vortec a good engine?
The best-known and most-beloved has to be the “350” or 5.7-liter version; especially with Chevrolet and GMC trucks. They are powerful, tough, reliable and it is relatively easy to “soup up” or increase their performance.
What is so special about a Vortec engine?
The redesigned cylinder heads of a Vortec engine provides for improved combustion efficiency. The intake ports (reshaped) of the engine provides for better cylinder filling and fuel atomization by promoting higher air flow velocities to the combustion chambers via the ports.
How much HP do heads add?
A set of heads for your car will probably set you back $700. Your engine probably won’t breath much better because of your cam, the smaller combustion chamber might bump your compression up a couple of points. You might get 20 hp or so.
Can you put 400 heads on a 350?
400 heads on a 350 block is a great way to increase your midrange and top end power. The swap is a direct bolt – on deal, you just need to be sure to use 400 head gaskets when you do the swap.
Are all center bolt heads vortec?
Not all center bolt heads are Vortec heads. … In the older heads, the center 4 intake manifold bolt holes are drilled at a 73 degree angle to the intake face of the head, as opposed to the older style heads, where all the intake manifold bolt holes are drilled at a 90 degree angle to the intake face of the cylinder head.
Can you convert a TBI to a Vortec?
That said, TBI can be adapted to a Vortec headed engine by using a GMPP or Edlebrock intake that bolts to Vortecs at one and and TBI at the other. The other simple swap is to use the Swirl Port heads off earlier engines and the TBI bolted to a Vortec bottom end.