- How do I know what breaker to use?
- What size fuse should I use for LED lights?
- Can you use 5 amp fuse instead 3?
- How can you tell if a plug fuse is blown?
- How many type of fuse are there?
- How many watts can a 3 amp fuse take?
- How do I know what size fuse I need?
- Can you use 13a fuse instead 3a?
- Can I replace a 15 amp breaker with a 20 amp breaker?
- How many watts can a 5 amp fuse take?
- How many outlets can be on a 15 amp breaker?
- How do you tell if a fuse is blown on a circuit board?
- Can I use a 3 amp fuse instead of a 2.5 amp?
- Can I put a 10amp fuse in a 5 amp?
- What does a double 100 amp breaker mean?
- How do you size a 12v fuse?

## How do I know what breaker to use?

Circuit breakers have markings stamped on the side of them and are usually located inside the panel cover door.

There is a label that will tell you what type of breaker is needed for installation in that particular panel..

## What size fuse should I use for LED lights?

75mm is good for about 7.5 amps max. I generally like to have at least 100% extra rating so a 3 amp fuse max is what i would use. This should be plenty for 4 leds. If you have working leds but blow a 10A fuse i think your wiring needs checking and you will probably find your fuse is directly across the battery.

## Can you use 5 amp fuse instead 3?

If you replace it with a 5A fuse you will lose part of the protection the 3A fuse was intended to provide. … Thus it is unwise to replace a fuse with one which can carry more current. If you unwisely choose to replace a fuse with one with a higher current rating, first make sure that your fire insurance is up to date.

## How can you tell if a plug fuse is blown?

Remove the fuse from its holder. In some cases you may need a small screwdriver to unscrew the fuse holder cap. Look at the fuse wire. If there is a visible gap in the wire or a dark or metallic smear inside the glass then the fuse is blown and needs to be replaced.

## How many type of fuse are there?

Fuses can be divided into two major categories, AC fuses, and DC fuses. The below block diagram illustrates the different types of the fuse under each category.

## How many watts can a 3 amp fuse take?

700 wattsPlugs for appliances rated up to about 700 watts should have a 3-amp fuse (coloured red). For example: 3A Fuse – Table lamp, standard lamp, television, video, computer, mixer, blender, fridge, freezer, power drill, jig saw, soldering iron.

## How do I know what size fuse I need?

Fuse rating = (watts/volts) x 1.25Note the power of the appliance – usually in the appliance manual,Note the voltage (240 volts in the UK).Use the next highest fuse rating after the calculation. Say the calculated fuse rating is 2.2679 amps, use a 3 amp fuse.

## Can you use 13a fuse instead 3a?

For an appliance rated as 700W or less, a 3A fuse should be fitted. For appliances above 700W, a 13A fuse should be fitted. … BS1363 has standardised on just two preferred fuse ratings, 3A and 13A, however any fuse rating up to 13A can still be used.

## Can I replace a 15 amp breaker with a 20 amp breaker?

The answer: It’s possible, but not advisable without an electrician evaluating the situation. You should never just upgrade from a 15-amp breaker to a 20-amp one just because the current one is tripping. Otherwise, you may burn your house down via electrical fire.

## How many watts can a 5 amp fuse take?

1150 WattsIf your lighting circuit at home is protected by a typical 5 amp fuse you can multiply this by the voltage to get 1150 Watts.

## How many outlets can be on a 15 amp breaker?

eight lightsTypically, you can have no more than eight lights or electrical outlets on a 15-amp circuit. To determine the amp rating of a circuit, just look at the number on its breaker or fuse in your main electrical panel.

## How do you tell if a fuse is blown on a circuit board?

2 Check the circuit board for fuses. If you find one, pull it out with the long-nose pliers and see if it appears to be blown. If you have a glass fuse, look at the filament inside. A blown fuse will have a broken filament.

## Can I use a 3 amp fuse instead of a 2.5 amp?

Yup. The fuse is there to protect the wiring and 3 amp is well within the supply wire’s capability. Re: Radio calls for a 2.5 amp fuse.

## Can I put a 10amp fuse in a 5 amp?

Possibly yes. What ever is wired into that 5 amp slot is rated for a max of 5 amps, overdrawing more than 5 amps by removing the 5 amp fuse and putting in a 10 amp fuse can possibly short out a circuit. Never replace a blown fuse with a higher-amp fuse. …

## What does a double 100 amp breaker mean?

It depends on what you mean when you say it has double 100 amp breakers. If you mean the breaker has 2 handles that are tied together and both handles say 100 amps then no it is only a 100 amp service. If you see 4 handles tied together then it would most likely be 200 amps.

## How do you size a 12v fuse?

Find the size of fuse by multiplying the amps required by the device (2) by 1.5. 2×1.25 = 2.5 then we will round up to the nearest fuse size (in multiples of 5 amps) which would call for a 5 amp fuse.